Yes — brick is one of the best surfaces you can mount a home EV charger on. Masonry is solid, flat and does not flex, so a wallbox fixed to it stays fixed. The checks are simply different from timber or siding: what the wall is actually built from, where its mortar joints and damp-proof course sit, and how the cable will get through. Those details decide the fixing, which is why they belong to the installer, not to guesswork.
Key Takeaways
- Brick is an excellent mounting surface: solid, flat and free of flex.
- The checks are masonry-specific — wall build, mortar joints, damp-proof course, cable entry and surface condition.
- Fixing choice belongs to the installer after surveying the wall; no surface should be treated as generic.
- A weak, protected or shared wall points to a post or pedestal mount instead.
Why Brick Suits a Wall-Mounted Charger
A wall charger is not heavy like an appliance, but it is not light either, and a charging cable pulls and twists at it every day for years. Brick carries that load without creeping or cracking around the fixings the way soft surfaces can. It also tolerates outdoor weather on the wall face itself, and most homes offer a brick wall exactly where the car parks — the house wall beside the driveway or the garage wall. If you are comparing surfaces, our guide to installing on vinyl siding shows how different the approach is on a flexible skin, and the mounting-height guide covers where on the wall the unit should sit.
The Masonry Checks That Come First
| Check | Why it matters | Who decides |
|---|---|---|
| What the wall is built from | Solid brick, cavity wall, block and rendered or stone finishes all take fixings differently | The installer, by inspecting the wall |
| Brick or mortar | Fixings hold in the brick itself; soft mortar joints are not a fixing surface | The installer, when marking out |
| Damp-proof course and water paths | Holes and cable entries must not bridge the damp-proof layer or channel water into the wall | The installer |
| Cable route through the wall | The entry point decides drilling, sealing and how tidy the internal run to the consumer unit can be | The installer, with your preference on looks |
| Condition of the surface | Spalled, crumbling or cracked brick may not hold; a sound section or another position may be needed | The installer |
None of this is a reason to expect problems. It is the ordinary survey an installer does before drilling any wall, and on a sound brick wall the answers are usually simple. What the table replaces is the one approach that causes damage: treating every wall as if it were the same.
When the Brick Wall Is Not the Answer
Three situations point elsewhere. The wall is a thin garden or boundary wall rather than a house wall — that is a structure question first, and it may not be yours alone to decide. The building is listed or protected, where fixings into the fabric need permission before any drilling. Or the brickwork is genuinely poor in the only spot the car can reach. In each case the fallback is a post or pedestal mount standing off the wall, which our wallbox installation guide places alongside wall mounting, or a different wall on the same building.
Wallboxes Built for the Wall
For a hard-wired wall installation, the EVDANCE EV-ACT5006T 48A Level 2 wall charger (up to 48 A, hard-wired or NEMA 14-50P, NACS, 25 ft cable, IP65/IP66, ETL/FCC/CE) suits North American homes. For Type 2 markets, the EV-ACT3204PE 22 kW wallbox (three-phase, cable or socket, RFID and app control, CE) is the wall-mounted option. Either way, the mounting itself is installer work: on a continuous load like EV charging, the circuit behind the wall matters as much as the fixings in it.
Frequently Asked Questions
Can a charger be mounted on a rendered or painted brick wall?
Usually yes — what matters is the masonry underneath the finish, not the finish itself. The installer checks the substrate before fixing, and the unit’s seal sits against the wall face.
Will drilling into brick damage my wall?
Done with the right fixings in the right places, it is routine work that leaves four small holes if the charger is ever removed. Done in the wrong places — mortar joints, the damp-proof course — it can cause harm, which is why it is installer work, not a DIY job.
What if the only wall near my parking space is a fence or garden wall?
Then treat it as a structure and ownership question before treating it as a mounting question. A post or pedestal mount beside the parking space is often the better answer.
Related Reading
- How to Install an EV Charger on Vinyl Siding
- How High Should an EV Charger Be Mounted?
- Wallbox Home Charger Installation Guide 2026
- What Is a Standard EV Charger Installation?
