Making the EV-AC04001U permanent means docking it, not rewiring it: a cradle for the control box, a holster shaped for its J1772 connector, and a hook for the cable turn this 40 A portable into a fixed daily station. What the mounting kit for this model actually contains is a question to confirm before you buy — the model’s specification lists the charger, not the hardware — and the unit stays a plug-in device throughout.
Key Takeaways
- A permanent dock has three parts — cradle, J1772-shaped holster, cable hook — all matched to this charger.
- The model’s specification names the charger, not the hardware: confirm what the kit contains, in writing, before ordering.
- The J1772 holster carries the handle so its latch sits unloaded between sessions.
- Permanent means docked, not hardwired: the unit stays a plug-in charger, and the plug stays reachable.
The Three Parts of a Permanent Dock
| Part | Its job | Confirm for this unit |
|---|---|---|
| Control-box cradle or bracket | Carries the unit’s weight on the wall, so neither the wall plug nor the cable does | That a bracket or mounting points exist for this model, included or as a separate accessory |
| J1772 holster | Parks the connector with its face protected — its resting place after every session | That the holster is moulded for J1772 (a NACS or Type 2 dock will not hold this connector) and whether a cap is part of it |
| Cable hook | Holds the 25 ft cable in a loose coil off the floor | That the hook suits the cable’s weight and length |
A kit is only complete when all three parts match this charger — its box, its connector standard, its cable length. A generic “EV charger mounting kit” bought without those checks is how a dock ends up holding the cable and nothing else.
What to Confirm Before You Order the Hardware
- Included or separate? Ask what the box contents list actually names. If no bracket or holster is listed, both are accessories to add to the order — confirmed as such, not assumed.
- Made for this model? A cradle is shaped for one control box. Confirm the bracket fits this unit’s housing rather than a sibling model with a different case.
- Fixings for your wall. A dock holding a charger and a swinging cable needs a solid fixing — stud, masonry or a post. Ask what fixings the kit assumes; our guide to how high a charger should be mounted covers the height side.
- The plug stays reachable. On a plug-in unit, unplugging is the disconnect. However permanent the dock feels, the plug and outlet must stay accessible — never trapped behind the box.
Parking a J1772 Handle, Specifically
The J1772 handle carries a latch on top — the catch that locks it into the car. Docked properly, the holster takes the handle’s weight and the latch sits unloaded; hung by its cable, the same connector takes knocks on exactly the part that has to click cleanly into the car. A J1772-shaped holster also holds the face at its designed angle, so the contacts stay sheltered between sessions. The broader habits — loose coils, nothing on the floor — are covered in our guide to hiding and managing a charging cable, and the cable length guide helps judge reach from the docked position.
What Permanent Does Not Change
Docked, the EV-AC04001U remains what it was made as: a plug-in portable charger (40 A, 9.6 kW, NEMA 14-50P, IP66, 3-year standard warranty). Permanent never means hardwiring it — cutting off the plug modifies a product built and sold as a plug-in appliance, and it is electrician territory besides. The circuit rule is unchanged: 40 A of continuous load sits on a 50 A circuit, sized at 125%. And the travel option survives the dock: unplug, unclip, and the charger is portable again — the honest difference between docking a portable and installing a wallbox, a choice our guide to where to install a home charger helps frame.
Frequently Asked Questions
Is a wall holster and mounting kit included with the EV-AC04001U?
Do not assume either way — check the box contents for your order and ask the seller to confirm in writing. If the hardware is not listed, it is a separate accessory, chosen by the three checks in the table above.
Can I hardwire the charger to make it truly permanent?
No. It is built as a plug-in device and the plug is its disconnect. A hardwired installation is a wallbox job for a licensed electrician — docking is how a portable goes permanent.
Does docking the charger affect its warranty?
Mounting a charger the way the manufacturer provides for is normal use. Modifying the case or cutting the cable is not — if the mounting provision is unclear, ask the manufacturer before drilling anything.
Related Reading
- How High Should an EV Charger Be Mounted?
- How to Hide and Manage an EV Charger Cable
- EV Charger Cable Length Guide: 5 m, 7.5 m or Longer?
- Where Should You Install a Home EV Charger?
